Model
12
(shown with tan grill, also available
with black or creamy white grill, email
to specify)
The -10 dB frequency response of the Model
12 referenced to its 1 kHz response as an indication of it's
in-room response, is an incredible 30 Hz. Except for a 2.5 dB
rise in bass response at 150 Hz, that is intended to give pitch
definition to the mid bass, the frequency response of the Model
12 is flat from 55 Hz to 20 kHz +/- 3.5 dB.
see frequency response
This speaker delivers
real bass and large speaker performance with the finesse of the
Model 10S
This
speaker has a very similar presentation to the Model 10S, however, it has surprisingly nice,
robust, extended bass response, and high output, the kind you
will not find in a speaker of this size. Why, because the SEAS
woofer, the same kind used in the Model 10S, is known for its
potent bass response and given that we are using two of them
in a larger cabinet, this speaker has faster bass and better
bass extension than most speakers with 6.5 inch woofers. Plus
this speaker is magnetically shielded to allow it to be used
very close to CRTs including as a center channel loudspeaker.
The ideal complement to the Model 10S and Modl 25. |
This loudspeaker is very musical
and has exceptional bass response.
-6dB referenced to 1kHz
output: 35Hz.
-10dB referenced to 1kHz output: 30Hz.
Available in light real plywood finish as shown, with black
grills.
Magnetically
shielded
Condition: new cabinets
and parts,
Regularly
$1695 per pair
NOW: $1,095 per pair
free shipping
|
The Model 10
Ultra Definition
Minimonitor
"I
recently purchased a pair of your model 10 speakers.... I like
them very much... a big step up from my old NHT Superzeros in
terms of smoothness and inner detail. Their laid back balance
is a nice complement to my Adcom/Rotel electronics. I have shopped
them around against many contenders in the price range: Snells
and Quad 11Ls - a brighter image but fatiguing peaky sound. JMLAB
Chorus, Paradigms - Model 10 was better detailed, Spendor s3/5
- very similar overall sound, Totem Mites - comparable in many
ways, a little brighter, B&W CDM1s - the only speaker that
I preferred over the 10 overall (but too big for my setup)." (Customer) |
SPECIFICATIONS:
Dimensions: 5.5 X 10 X 6.5 (W x H x D)
Frequency Response: 55Hz-20kHz, +/- 3dB
-6dB referenced to 1kHz: 35Hz. (not
a typo)
Sensitivity: 83.5dB 1/watt/m
Rated Impedance: 8 ohms
Cabinet construction: Cross-braced half inch MDF or wood board
Finish: satin black lacquer, or light wood
Weight: 16 pounds per pair
Recommended amplifier: 45-200 watts
Regular price:
$995 per pair
Sale
Price!
1 pair
$895 per pair
(free shipping)
|
|
The
PSM Super Monitor:
Same performance, discontinued
cabinet style
Dimensions: 24 X 7.5 X 16 inches
(H X W X H)
Frequency Response: 35
Hz to 20 kHz +/- 3.5 dB
Hybrid Acoustic
Suspension and Folded Transmission Line Design
the
imaging of a minimonitor, the dynamics of a large floor stander
PSM Un-Smoothed Anechoic
Response
-10dB referenced to midband
(1kHz) response: 28Hz
Compare
this speaker to any large bookshelf loudspeaker. The PSM Super
Monitor will outperform just about any large monitor regardless
of price. |
SUPER
CLEARANCE PRICE!
your
chance to get one of the best large monitors
1 pair satin black
Regularly: $3,995 per pair
Sale: $1995 per pair
free shipping!
Ask about special on custom Super Monitor stand. One
additional Super Monitor available. Imagine three of these across
the front in a theater system. |
 SANDBAGS
24 inch fill-able STANDS
How to get the
best sound out of small speakers
"I
am amazed at how much better the 20's sound on your sandbag stands..I
had them previously on an expensive pair of Osiris stands and
it is no contest. I too never understood metal stands as they
ring even when
mass loaded." Customer
You
would not buy metal loudspeakers. Then why buy metal stands.
Most loudspeaker stands are made from metal tubes because it
is convenient, easy and inexpensive. Sandbags stands are fabricated
from high density anti-resonant medite board, the same material
used to make the finest loudspeakers. All edges are rounded and
the stands are finished in high quality satin black lacquer paint.
They provide a rock solid base for larger minimonitors and bookshelf
size loudspeakers. |
"The
stands, which are ... fairly heavy, complement speakers well."
(Andrew Kwiran, The Absolute Sound Vol. 19, Issue 97)
Regularly $695 per pair
Sale! $495 per
pair
1 pair available
at this price
free shipping!
|
The handcrafted
IW3.5 Audiophile
Mini In-wall Point Source
loudspeaker
(Or, the Role
Audio Skiff In-wall/In-ceiling Speaker)
Faceplate Dimensions: 4.5 inches wide by 4.5 high by 3/4
inches deep
Clearance: 2.5 inches clearance, including 1/2 inch wall
material)
Cutout: 3&7/8 by 3 & 5/8 inches
Clearance between studs: 5 &3/4 inches |
The smallest and most advanced
in-wall loudspeaker. A small in-wall loudspeaker that can handle
demanding orchestral music
.
You can buy any run of the mill re-badged in wall speaker or
you can buy this speaker which we design off the Role Audio skiff
and hand craft in-house. The baffle is raised 3/4 inch off the
wall for stunning imaging.
Now get all
the performance of a small minimonitor from an in-wall loudspeaker!
Price: $199.95
each
Sale : $175 each
free shipping!
|
SUPER
SPECIAL CLEARANCE
SALE!
 
Here is
a great solution when you want a great pair of wall mounted,
or behind the desk wall-mounted minimonitors for a smaller area
or you just cannot use in wall speakers for rear speakers! Because
the OW3.5 use a single driver and they are raised 3.25 inches
off the wall, they image better than any in-wall speaker and
provide a more coherent sound.
The OW3.5 On-wall Audiophile Point Source Loudspeaker
The design of the OW3.5 on-wall
is inspired by our Role Audio Skiff loudspeaker. The OW3.5 is
a point source loudspeaker that is designed for on-wall mounting.
It is intended for front, center, and rear loudspeaker use as
a substitute for floor standing and bracket mounted loudspeakers.
As a single driver loudspeaker with neutral response over its
operating range, it offers a high level of performance and the
ultimate flexibility in focusing and distributing sound especially
in difficult and unusual room configurations. Installation is
very simple. The speaker
is secured with a single
molly bolt, toggle bolt, or wood screw to the wall. The speaker
slides onto the bolt or wood screw. Or, to be able to direct
the sound, use an Omnimount 10.0 series bracket with the preinstalled
bracket receptacle. Wire connections are via spring loaded push
terminals. |
The easiest
possible hook-up
SUPER SPECIAL
CLEARANCE SALE!
Regularly
$174.95 each
ONLY
2 LEFT!
Special Sale
Price: $85
each
free shipping!
SPECIFICATIONS:
Dimensions: 7.5 X 6.5 X 3.25 inches
(L
X W X D)
On-wall Frequency Response: 95 Hz - 20 kHz, +/- 5 dB
Sensitivity: 88 dB 1/watt/m
Rated Impedance: 8 ohms
Driver: 3.5 full range cast frame PPM cone
Weight: 3.5 pounds each.
The easiest possible
hook-up
The OW3.5 on-wall loudspeaker
is one of the easiest solutions to getting high quality sound!
You can drive a screw or nail
into the wall and simply hang the speaker on it or remove the
sealing screw and attach an Omnimount 10 series bracket to it.
Either way you will be rewarded by amazing full range open sound
with surprising imaging. The OW3.5 are very efficient and very
easy to drive. |